| vwown3d | 07-19-2005 08:36 PM |
Changing Window Buttons Color! (start)
�
�
Decided to give this a try on the 05(will finish this week) :
First , take the whole assembly out of the car:
Ulplug the two plugs by pressing in the tabs and pulling the plugs out:
Next take the switch panel off of the whole assembly VIA the 3 screws:
Next, pop the switches off of the circuit board, i used 4 nails to hold the tabs back but you can use anything (mines lined up backwards for this pic so the tabs dont line up but i circled them):
Next, locate the two leads shown, one is the POS(+) and the other is the NEG(-). with Led's you need to know which one is which because LED's are polar and only run one way. ( They run between 11 and 12.5 Volts) (numbers 2 and 4 by counting pink dots) EDIT FOR SOME REASON THE LED'S ALL GO OFF WHEN YOU PUT THE DRIVERS REAR WINDOW UP. THE LEADS ARE TIED INTO THIS SWITCH SO IM GOING TO FIND THE MAIN LEAD.
You need to solder two wires to these leads, i used one BLACK for NEG(-) and RED for POS(+) to make it easy.
As you can see the switches already have a clear part on the button when you light up the back so the LED's will just have to light up somewhere inside the circuit board housing.
MCD- the higher the brigheter
RED led's are around 2.0V forward diode voltage
5mm led's are around 20 Ma forward diode current
use this: to calculate the resistor you need:[URL=http://linear1.org/ckts/led.php]resistor calculator[/URL]
(use #'s on box of led's)
First , take the whole assembly out of the car:
Ulplug the two plugs by pressing in the tabs and pulling the plugs out:
Next take the switch panel off of the whole assembly VIA the 3 screws:
Next, pop the switches off of the circuit board, i used 4 nails to hold the tabs back but you can use anything (mines lined up backwards for this pic so the tabs dont line up but i circled them):
Next, locate the two leads shown, one is the POS(+) and the other is the NEG(-). with Led's you need to know which one is which because LED's are polar and only run one way. ( They run between 11 and 12.5 Volts) (numbers 2 and 4 by counting pink dots) EDIT FOR SOME REASON THE LED'S ALL GO OFF WHEN YOU PUT THE DRIVERS REAR WINDOW UP. THE LEADS ARE TIED INTO THIS SWITCH SO IM GOING TO FIND THE MAIN LEAD.
You need to solder two wires to these leads, i used one BLACK for NEG(-) and RED for POS(+) to make it easy.
As you can see the switches already have a clear part on the button when you light up the back so the LED's will just have to light up somewhere inside the circuit board housing.
MCD- the higher the brigheter
RED led's are around 2.0V forward diode voltage
5mm led's are around 20 Ma forward diode current
use this: to calculate the resistor you need:[URL=http://linear1.org/ckts/led.php]resistor calculator[/URL]
(use #'s on box of led's)
| thisisbrock | 07-20-2005 12:17 AM |
nice. cant wait to see finished pics.
| beastSTI | 07-20-2005 12:18 AM |
WOOHOO!! You should get rainbow colors! *limping wrist*
J/K
J/K
| LESLIEx317537 | 07-20-2005 12:28 AM |
Cool project, blue is my choice.
O yeah, if you find 6 volt LED's you can run two of them in series to a 12 volt connection. I think that should work.
Or if you find 3 volt LEDs run four of them in series.
resistors just take up space and power. :) You can get more light instead by using light emiting diodes.
[url]http://www.theledlight.com/ledcircuits.html[/url]
O yeah, if you find 6 volt LED's you can run two of them in series to a 12 volt connection. I think that should work.
Or if you find 3 volt LEDs run four of them in series.
resistors just take up space and power. :) You can get more light instead by using light emiting diodes.
[url]http://www.theledlight.com/ledcircuits.html[/url]
| VSGTS14 | 07-20-2005 12:49 AM |
bah i still want to convert my sti interior to all red...one day
| Bishop | 07-20-2005 12:57 AM |
this one's gonna need to be a sticky!
| MU5A5HI | 07-20-2005 01:05 AM |
Sweet, gonna have to try this in my 04.. i jsut finally managed to make my clock red so this is next. Thanks!
| smdandb2 | 07-20-2005 11:11 AM |
Damn the 02s for having gay switches!
| Chris Cuevas | 07-20-2005 01:23 PM |
Werd to that !!!
I cant wait to see this one !!!
Hurry up already !! I wanna finish of interior so that everything lights red !!
:banana:
I cant wait to see this one !!!
Hurry up already !! I wanna finish of interior so that everything lights red !!
:banana:
| Phy6 | 07-20-2005 01:49 PM |
+1 for stickyness
Show us your finished pics!
Show us your finished pics!
| Subawrx | 07-20-2005 05:05 PM |
[color=black]For a long time I have wondered if I could somehow replace the button controlling the passenger side window, with a 'one touch - down' button, like the one controlling the driver side window. Though, I did not realize that the whole assembly was on a single printed circuit board.[/color]
[color=black]Is the function that continues to supply power to the driver�s side window motor part of this circuitry? Also, how does the circuit know when the window is in the �down� position, is there a limit switch inside the door?[/color]
[color=black]Just wondering, now that you have it apart do you see any way this would be possible?[/color]
[color=black]Thanx in advance...[/color]
[color=black]Is the function that continues to supply power to the driver�s side window motor part of this circuitry? Also, how does the circuit know when the window is in the �down� position, is there a limit switch inside the door?[/color]
[color=black]Just wondering, now that you have it apart do you see any way this would be possible?[/color]
[color=black]Thanx in advance...[/color]
| vwown3d | 07-20-2005 10:44 PM |
I taped down the wired; down the sides to the back of the panel where they will connect to all of the LED's:
Here i drilled holes through the black casing only for the LED wires to stick through these wires will stick outside the casing into the door somewhere. NOTE BE CAREFUL NOT TO MESS UP ANY PART OF THE PIVIOT SWITCHES ARE YOU CUT AND/OR DRILL:
Here are 2 LED's sitting inside the switches ( you can see the backs they are pointing the other way toward the clear section on the switch):
This is it for today, ONE OF THE RESISTORS I GOT WAS BAD AND SET ON FIRE WHEN I WAS TESTING THE LED'S SO I GAVE UP FOR THE NIGHT sorry for the bad pics i was mad tired. Ill finish this tomorrow hopefully i just want to find a diff lead amd make sore my cars not gonna go up in flames like it could of.
LED's im using are RED 1.7V 20MA 3000 MCD led's with 1k resistors. the reccomended resistors are 680 ohms at 15V so im playing it a little on the safe side.
Here i drilled holes through the black casing only for the LED wires to stick through these wires will stick outside the casing into the door somewhere. NOTE BE CAREFUL NOT TO MESS UP ANY PART OF THE PIVIOT SWITCHES ARE YOU CUT AND/OR DRILL:
Here are 2 LED's sitting inside the switches ( you can see the backs they are pointing the other way toward the clear section on the switch):
This is it for today, ONE OF THE RESISTORS I GOT WAS BAD AND SET ON FIRE WHEN I WAS TESTING THE LED'S SO I GAVE UP FOR THE NIGHT sorry for the bad pics i was mad tired. Ill finish this tomorrow hopefully i just want to find a diff lead amd make sore my cars not gonna go up in flames like it could of.
LED's im using are RED 1.7V 20MA 3000 MCD led's with 1k resistors. the reccomended resistors are 680 ohms at 15V so im playing it a little on the safe side.
| Phy6 | 07-20-2005 11:49 PM |
[QUOTE=LESLIEx317537]Cool project, blue is my choice.
O yeah, if you find 6 volt LED's you can run two of them in series to a 12 volt connection. I think that should work.
Or if you find 3 volt LEDs run four of them in series.
resistors just take up space and power. :) You can get more light instead by using light emiting diodes.
[url]http://www.theledlight.com/ledcircuits.html[/url][/QUOTE]
Thanks for the link, that site and the ones it links to are great!
O yeah, if you find 6 volt LED's you can run two of them in series to a 12 volt connection. I think that should work.
Or if you find 3 volt LEDs run four of them in series.
resistors just take up space and power. :) You can get more light instead by using light emiting diodes.
[url]http://www.theledlight.com/ledcircuits.html[/url][/QUOTE]
Thanks for the link, that site and the ones it links to are great!
| Phil Jr. | 07-21-2005 02:07 AM |
that nissan logo is so very odd.
| 949 | 07-21-2005 03:02 AM |
hurry i want to see this awesome mod. if you also do the mod so that they have auto up and down. shissttt im willing to do this in a second.
| makanai | 07-21-2005 07:00 PM |
excellent post so far, can't wait to see finished product.
| imprezaboi | 07-21-2005 08:15 PM |
[QUOTE=Phil Jr.]that nissan logo is so very odd.[/QUOTE]
Not odd at all subaru and nissan actually share lots of similar parts. A shining example would be the 300zx 4 pots vs subaru jdm 4 pots they are relatively identical.
Not odd at all subaru and nissan actually share lots of similar parts. A shining example would be the 300zx 4 pots vs subaru jdm 4 pots they are relatively identical.
| 762x51 | 07-21-2005 08:38 PM |
The STi intercooler spray button also has Nissan on it. Just did the red light mod on that and saw it....had to double check and make sure I wasn't working on my Pathfinder. :D
| vwown3d | 07-21-2005 09:14 PM |
started off fresh today:
THIS IS WHERE THE NEGATIVE(-) POST SHOULD GO. VOID THE OTHER PIC:
[IMG]http://www.imagestation.com/picture/sraid178/pc3071d356670953802fb2ddfe72d7a77/f328e7da.jpg[/IMG]
Bend the LED"S like this to get them to point down in the housing.
[IMG]http://www.imagestation.com/picture/sraid178/pca9e4c346b56f3529b564dc8ff5b48f8/f328e885.jpg[/IMG]
Here is one LED tape and in the hole:
[IMG]http://www.imagestation.com/picture/sraid178/pe5afdc120acf9c69a8ed09ac26cac014/f328e7ad.jpg[/IMG]
This is one side done with the wires hanging extra llong:
[IMG]http://www.imagestation.com/picture/sraid178/p1efdd47b9f3eafe90bd5293d0e9adaef/f328e875.jpg[/IMG]
Now all you have to do is plug the switch in and move around the LED's with something long and skinny to get them to shine in the exact spot. Solder all the wires together and give it a good tape job.
(ill post the pics of inbetween steps over the weekend, i just wanted to get the finished product done!!!!!!!)
here is mine all taped up and tested ready to go in the car:
[IMG]http://www.imagestation.com/picture/sraid178/p1f36197891dcd65f2493576747158e98/f328e7b7.jpg[/IMG]
blury but in car:
[IMG]http://www.imagestation.com/picture/sraid178/pb0be8df174542d3e7ddc943007f296f4/f328e7b4.jpg[/IMG]
more:
[IMG]http://www.imagestation.com/picture/sraid178/pdfccf5ebe5ba2c545e6cad1ee9c78bf5/f328e88d.jpg[/IMG]
THIS IS WHERE THE NEGATIVE(-) POST SHOULD GO. VOID THE OTHER PIC:
[IMG]http://www.imagestation.com/picture/sraid178/pc3071d356670953802fb2ddfe72d7a77/f328e7da.jpg[/IMG]
Bend the LED"S like this to get them to point down in the housing.
[IMG]http://www.imagestation.com/picture/sraid178/pca9e4c346b56f3529b564dc8ff5b48f8/f328e885.jpg[/IMG]
Here is one LED tape and in the hole:
[IMG]http://www.imagestation.com/picture/sraid178/pe5afdc120acf9c69a8ed09ac26cac014/f328e7ad.jpg[/IMG]
This is one side done with the wires hanging extra llong:
[IMG]http://www.imagestation.com/picture/sraid178/p1efdd47b9f3eafe90bd5293d0e9adaef/f328e875.jpg[/IMG]
Now all you have to do is plug the switch in and move around the LED's with something long and skinny to get them to shine in the exact spot. Solder all the wires together and give it a good tape job.
(ill post the pics of inbetween steps over the weekend, i just wanted to get the finished product done!!!!!!!)
here is mine all taped up and tested ready to go in the car:
[IMG]http://www.imagestation.com/picture/sraid178/p1f36197891dcd65f2493576747158e98/f328e7b7.jpg[/IMG]
blury but in car:
[IMG]http://www.imagestation.com/picture/sraid178/pb0be8df174542d3e7ddc943007f296f4/f328e7b4.jpg[/IMG]
more:
[IMG]http://www.imagestation.com/picture/sraid178/pdfccf5ebe5ba2c545e6cad1ee9c78bf5/f328e88d.jpg[/IMG]
| vwown3d | 07-21-2005 09:29 PM |
more:
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG]
Radio
[IMG]http://www.imagestation.com/picture/sraid178/pac225a207e1ace6231eeb5a5833afb4d/f328e79d.jpg[/IMG]
Center and weird shot of headlights:
[IMG]http://www.imagestation.com/picture/sraid178/pa2d2fde9dd48681f6b0fc6447516cbba/f328e7f3.jpg[/IMG]
My back 2 are a little dimmer and need adjusting but im tired. :o all you have to do is push the LED in or out or adjust the side to side a little.
I will prob redo the whole post this weekend and put it in one long step if we can get this sticky. if not, at least it will be organized. Ill also try to take some better pics.!
ENJOY and watch out there a lot of thigs that can go wrong with this job. lol :disco:
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG]
Radio
[IMG]http://www.imagestation.com/picture/sraid178/pac225a207e1ace6231eeb5a5833afb4d/f328e79d.jpg[/IMG]
Center and weird shot of headlights:
[IMG]http://www.imagestation.com/picture/sraid178/pa2d2fde9dd48681f6b0fc6447516cbba/f328e7f3.jpg[/IMG]
My back 2 are a little dimmer and need adjusting but im tired. :o all you have to do is push the LED in or out or adjust the side to side a little.
I will prob redo the whole post this weekend and put it in one long step if we can get this sticky. if not, at least it will be organized. Ill also try to take some better pics.!
ENJOY and watch out there a lot of thigs that can go wrong with this job. lol :disco:
| vwown3d | 07-21-2005 11:41 PM |
wow pics are not working, will fix tomorrow midday when i get out of work
| vwown3d | 07-22-2005 06:19 PM |
i think i fixed the pics!
| quest | 07-22-2005 06:48 PM |
coolio...nice work! The first new pic is still locked, but the rest work if you copy and paste the link
| 128d | 07-22-2005 09:14 PM |
looks nice.
| Undepelo | 07-25-2005 09:07 AM |
[QUOTE=vwown3d]i think i fixed the pics![/QUOTE]
Fix'em again!! :mad:
Fix'em again!! :mad:
| not ur avg girl | 07-25-2005 10:47 AM |
would you please just use photobucket?
nice work though... i'm impressed :disco:
nice work though... i'm impressed :disco:
| LESLIEx317537 | 07-25-2005 11:44 AM |
I'm going to power mine using the cig lighter, and run a wire to the left door.
I took mine apart and was looking and sucks how only the driver window things can glow. Can we find other switches?
Maybe from a Maxima?
I took mine apart and was looking and sucks how only the driver window things can glow. Can we find other switches?
Maybe from a Maxima?
| Undepelo | 07-25-2005 11:53 AM |
FYI
If you look at the board there are empty soldering points for 3 more LED's.
I was going to get the OEM type LED's to solder on the board just like the green ones that are all ready there, but there is no voltage to the existing empty locations.
If you look at the board there are empty soldering points for 3 more LED's.
I was going to get the OEM type LED's to solder on the board just like the green ones that are all ready there, but there is no voltage to the existing empty locations.
| USA 79S | 07-26-2005 10:55 AM |
hmmm pics stop where the good stuff starts.
| sil0nt | 07-26-2005 03:03 PM |
all 4 of the 2005 outback switches light up (amber). i just got one for a rental and noticed immediately.
| LESLIEx317537 | 07-26-2005 04:54 PM |
Do the Outbacks switches look the same?
I wonder if we can just plug it in.
Cool...
I wonder if we can just plug it in.
Cool...
| not ur avg girl | 07-27-2005 01:18 PM |
working on fixing the pix, right now i am doing a retro fit with ALL FOUR windows auto up and down. i found the exact switches from a certain car and am hoping this will turn out. a little more on the $$ side tho.
| MoJack | 07-27-2005 02:01 PM |
Anybody with pics of a red '05 center console? If so, is the procedure like that of the '03 mod that is up?
| Phy6 | 07-27-2005 04:29 PM |
[QUOTE=not ur avg girl]working on fixing the pix, right now i am doing a retro fit with ALL FOUR windows auto up and down. i found the exact switches from a certain car and am hoping this will turn out. a little more on the $$ side tho.[/QUOTE]
Oooo that sounds cool. Did you get them from a Nissan? Please let us know!
Oooo that sounds cool. Did you get them from a Nissan? Please let us know!
| wrichiex_sti | 07-28-2005 11:48 AM |
looks nice
| intence | 07-29-2005 12:40 PM |
pics b0rked. bump
| USA 79S | 07-29-2005 12:45 PM |
dude, can you e-mail the pics to [email][email�protected][/email]
| VSGTS14 | 07-29-2005 03:35 PM |
fix the other pics, i need to know where the positive wire has to go.
i can see where the negative does!
i can see where the negative does!
| VSGTS14 | 07-29-2005 07:19 PM |
nvm i just did this mod today and will post a HOW TO on iwsti
| offset | 07-29-2005 08:18 PM |
[QUOTE=VSGTS14]nvm i just did this mod today and will post a HOW TO on iwsti[/QUOTE]
Why are you holding out on us NASIOC folks??
offset
Why are you holding out on us NASIOC folks??
offset
| ardinos | 07-29-2005 08:29 PM |
I've been doing the mod for people for eons but have never gotten around to documenting it. Nice job!
One suggestion, for 120 MCD is plenty bright, people should be warned the LED's for the door/window switch don't dim!
Also, if you leave the stiff wire lead attached to the LED instead of cutting it off and bend them properly, it helps keep the LED's positioned correctly and you don't even need wires. You simply tape down the stiff wire lead to hold the LED in place properly.
I would suggest putting electrical tape down on the switch face where you run the wires and place the LED's to prevent shorts. Also electrical tape is a great way to cover the green LED's and leave them in place in case you want to return to stock in the future.
One suggestion, for 120 MCD is plenty bright, people should be warned the LED's for the door/window switch don't dim!
Also, if you leave the stiff wire lead attached to the LED instead of cutting it off and bend them properly, it helps keep the LED's positioned correctly and you don't even need wires. You simply tape down the stiff wire lead to hold the LED in place properly.
I would suggest putting electrical tape down on the switch face where you run the wires and place the LED's to prevent shorts. Also electrical tape is a great way to cover the green LED's and leave them in place in case you want to return to stock in the future.
| VSGTS14 | 07-29-2005 11:49 PM |
[url]http://www.imprezawrxsti.com/forums/showthread.php?p=304582#post304582[/url]
| LESLIEx317537 | 07-30-2005 06:34 PM |
Cool, I'm going to see if the hazard button can light up.
Edit:
Oops, just took my hazard button apart and found a small bulb inside and probed it to find 12 volts. So my bulb is burnt. Anyone know a part #?
Edit:
Oops, just took my hazard button apart and found a small bulb inside and probed it to find 12 volts. So my bulb is burnt. Anyone know a part #?
| LESLIEx317537 | 07-31-2005 01:32 AM |
I just did this mod and did it slightly different, but borrowed ideas from all.
When you press the window lock button, the leds go off. I used 120mcd red leds from radioshack and they look awesome.
When you press the window lock button, the leds go off. I used 120mcd red leds from radioshack and they look awesome.
| Thingfish | 08-01-2005 09:11 AM |
I did mine in Blue. WAY too bright..... I did mine differently, and did all power from the board, and all internal. No external wires or power. A 3 dollar photo sensor keeps them off in daylight.
| LESLIEx317537 | 08-01-2005 11:27 AM |
Yo, how to hook up the 3 dollar photo sensor? Any pics where you mounted the eye?
I wired mine all internally also, and it the lights go off when you press window lock.
I used Red 120mcd LED's, BLUE ones you used are probably 5000mcd. lol :)
I wired mine all internally also, and it the lights go off when you press window lock.
I used Red 120mcd LED's, BLUE ones you used are probably 5000mcd. lol :)
| Thingfish | 08-01-2005 12:09 PM |
The sensor is in the door, using the glass as a kinda " fiber optic " effect.
The blues are 1500mcd/1.5cd 470nm Roithners. Driven 3.5v each @ 20ma. They are actually much darker blue then the pic shows.
[URL=http://img160.imageshack.us/my.php?image=20050801doorlights00025yu.jpg][IMG]http://img160.imageshack.us/img160/2625/20050801doorlights00025yu.th.jpg[/IMG][/URL]
The blues are 1500mcd/1.5cd 470nm Roithners. Driven 3.5v each @ 20ma. They are actually much darker blue then the pic shows.
[URL=http://img160.imageshack.us/my.php?image=20050801doorlights00025yu.jpg][IMG]http://img160.imageshack.us/img160/2625/20050801doorlights00025yu.th.jpg[/IMG][/URL]
| LESLIEx317537 | 08-27-2005 04:07 PM |
But how come the other buttons don't light up? You should have added 3 more.
| DangBruhY | 11-02-2005 12:42 AM |
Damn, all the pictures have been taken down. :(
| vwown3d | 11-02-2005 09:27 AM |
here are some.
still working
[IMG]http://i22.photobucket.com/albums/b330/vwown3d/switch.jpg[/IMG]
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG]
still working
[IMG]http://i22.photobucket.com/albums/b330/vwown3d/switch.jpg[/IMG]
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG]
| veightkiller | 11-02-2005 11:02 AM |
pic's no worky!!
| BillyC | 11-02-2005 11:43 AM |
Just for a quick follow-up on this, the window switch/door lock cluster from an 02-03 Forester will also work, and has all 4 switches lighted. Also, if you notice every switch in the forester has a light built in, but, the WRX does not have the extra illumination wires ran into the door, I'm sure it wouldn't be hard to find some of these switches in a wrecking yard. I found the main driver's door cluster and swapped even with a guy that just simply didn't care if they lit up or not... :)
| vwown3d | 11-02-2005 11:57 AM |
[QUOTE=vwown3d]here are some.
still working
[IMG]http://i22.photobucket.com/albums/b330/vwown3d/switch.jpg[/IMG]
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG][/QUOTE]
these work?
still working
[IMG]http://i22.photobucket.com/albums/b330/vwown3d/switch.jpg[/IMG]
[IMG]http://www.imagestation.com/picture/sraid178/p63586b4b035e343625538269455d9c81/f328e7a8.jpg[/IMG][/QUOTE]
these work?
| 949 | 11-02-2005 12:10 PM |
so you dont need to cut the horizontal lines. they are already in there with the front drivers side?
| WRXdonkey | 10-03-2007 10:59 AM |
/subscribed for reference. I plan on starting this soon...
eliminating all green in the STI, putting in a gauge pod where the clock is, and going red on everything and replacing the stock head unit...
Looks great btw.
eliminating all green in the STI, putting in a gauge pod where the clock is, and going red on everything and replacing the stock head unit...
Looks great btw.
| 07otleSTi | 10-03-2007 12:47 PM |
Had a question, any 06 owners done this? is this any differnt? also, im pretty sure i only have 1 window button to light up. does anyone have step by step pictures? on where they put the leds and such? thanks if anyone has it
-Simon
-Simon
| WRXdonkey | 10-03-2007 04:10 PM |
[QUOTE=07otleSTi;19575386]Had a question, any 06 owners done this? is this any differnt? also, im pretty sure i only have 1 window button to light up. does anyone have step by step pictures? on where they put the leds and such? thanks if anyone has it
-Simon[/QUOTE]
I'm '06 and I intend to... probably won't get after it for another month or more... lots of crap going on, and other things to fix.
-Simon[/QUOTE]
I'm '06 and I intend to... probably won't get after it for another month or more... lots of crap going on, and other things to fix.
| irascible | 12-03-2007 06:35 PM |
[quote=WRXdonkey;19578017]I'm '06 and I intend to... probably won't get after it for another month or more... lots of crap going on, and other things to fix.[/quote]
I also have an '06 and am interested in doing this. I might tear down the gauge cluster to see what is needed. I'll take pictures as I go along if and when I have time to do it.
I also have an '06 and am interested in doing this. I might tear down the gauge cluster to see what is needed. I'll take pictures as I go along if and when I have time to do it.
Không có nhận xét nào:
Đăng nhận xét